1:4 HDMI Distribution Amplifier with 4K60 4:4:4 and HDR Support

Model: HD-DA4-4KZ-E

Splits one HDMI® source to two outputs
Handles 4K60 4:4:4 and HDR video signals
Fully compatible with HD 1080p, UHD 4K and DCI 4K sources and displays
Handles 3D video and Deep Color
Handles Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X® and uncompressed 7.1 linear PCM audio

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Related Products

Documents

The Crestron® HD- DA4-4KZ-E is a simple to use, high-performance 4K AV distribution amplifier designed to split a single HDMI® signal to feed two separate displays, switchers and/or other devices. It provides full support for UHD and DCI 4K60 4:4:4 and HDR video, HDCP 1.4 or 2.2 copy protection and high-bitrate 7.1 audio, to ensure optimal performance and compatibility for any HD or 4K video application. No programming or control system is required for operation.

Splits one HDMI® source to two outputs
Handles 4K60 4:4:4 and HDR video signals
Fully compatible with HD 1080p, UHD 4K and DCI 4K sources and displays
Handles 3D video and Deep Color
Handles Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X® and uncompressed 7.1 linear PCM audio
Selectable handling of HDCP 2.2 or HDCP 1.4
EDID management options
Input and output video presence indication
No programming or control system required
Thin profile - less than one inch deep
Surface, shelf or single rack rail mountable
External 100-240V universal power pack included

DA Audio Input - HDMI (Embedded)
DA Audio Output - HDMI (Embedded)
DA Video Input - DVI
DA Video Input - HDMI
DA Video Input - Other
DA Video Output - DVI
DA Video Output - HDMI
DA Video Output - Other
Spec Sheet available - Yes

COMMUNICATIONS:
•USB: USB 2.0 host; supports firmware update and custom EDID upload via a USB flash drive
•HDMI: HDCP and EDID (does not pass CEC)
•HDCP: Version Selectable for HDCP 2.2, 1.4 or OFF
HDCP encrypted content is blanked in OFF mode
•EDID Mode: Selectable for DEFAULT or COPY 1ST
The factory default EDID is 4K60 4:4:4 non-HDR video with 2-channel LPCM audio
The factory default EDID can be replaced with a custom EDID via USB
Sliding the switch from DEFAULT to COPY 1ST copies and stores the EDID from the device at OUTPUT 1 and passes it to the INPUT source device
Sliding the switch from COPY 1ST to DEFAULT erases the stored EDID and uses the factory default or custom EDID
Connectors:
•INPUT: (1) HDMI Type A connector, female
HDMI digital video/audio input[1]
(DVI and Dual-Mode DisplayPort compatible[2])
•OUTPUT 1-2: (2) HDMI Type A connectors, female
HDMI digital video/audio outputs[1]
(DVI compatible[2])
•SERVICE: (1) USB Type A connector, female
USB 2.0 host port
For firmware update and custom EDID upload via a USB flash drive
•24VDC 0.75A: (1) 2.1 x 5.5 mm DC power connector
24 Volt DC power input
PW-2407WU power pack included
Controls and Indicators:
•PWR: (1) Bi-color LED, indicates operating power is supplied via the power pack; illuminates amber while booting, green when operating
•SETUP: (1) Pushbutton and (1) red LED, restores factory settings
•RESET: (1) Recessed pushbutton for hardware reset
•INPUT: (1) Green LED, indicates video signal presence at the HDMI input
•OUTPUT 1 – 2: (2) Green LEDs, each indicates video signal transmission at the corresponding HDMI output
•HDCP (1) 3-position slide switch, selects the HDCP version (OFF, 1.4 or 2.2)
•EDID (1) 2-position slide switch, selects the EDID mode (DEFAUT or COPY 1ST)
Operating Temperature (Maximum): 104 F
Operating Temperature (Minimum): 32 F
Mount Type: Freestanding
AC Voltage (Maximum): 240 Volts
AC Voltage (Minimum): 100 Volts
Current Draw: 0.75 Amps
DC Voltage: 24 Volts
Depth: 4.67 in
Height: 0.87 in
Width: 8.07 in
Regulatory Compliance: CE, IC, FCC